Resulting in construction waste crushing equipment out of the reasons for the unqualified

construction waste crusher in use for a period of time, many users will find the discharge size is not uniform before the small, this problem if you do not find out the cause of the problem to solve a long time will lead to discharge of particle size unqualified situation . So what is the cause of this situation? Today, Hiroshi Heavy Industries Xiaobian give you a few more important factors cited, hoping to help users and friends, the following aspects as long as one by one investigation, as much as possible to help you solve the construction waste crushing equipment Discharge particle size of the reasons for failure. First of all, wearing parts, construction rubbish crushing equipment parts wear, including hammer, liner and a series of wear and tear, the other severe wear and tear of the hammer case, the operator should promptly replace the new hammer, Avoid affecting equipment output and efficiency, resulting in the destruction of construction waste crushing equipment. Second, the lack of motivation, if in operation, the power of power fails to meet the requirements, it will cause the rotor speed up, so that the power of the hammer does not meet the appropriate standards, resulting in the construction of waste crushing equipment Outlet size is too large. Again, the feed rate is too large, in the feeding process, if the speed is too fast, it will make the construction waste crushing equipment can not be timely and adequate crushing of materials, then there will be too large particle size of the finished product, a long time also Will cause the phenomenon of clogged materials inside the construction waste crushing equipment. Then, the crushed bearing temperature, during operation, the operator must pay attention to the bearing temperature, to keep below 70 degrees, if you find that the working temperature exceeds 70 degrees, there is a problem within the crushing equipment, the need to immediately stop running Check the bearing periphery failure. Finally, as long as the user does daily inspection work and regular maintenance work, the probability of occurrence of the above situations should be much smaller. As long as the normal operation of the construction rubbish crushing equipment, it will not delay the user's production, not because of Equipment failure lead to loss to users.

评论

发表评论

此博客中的热门博文

Artificial aggregate production process and advantages and disadvantages

Wool sand making machine by crushing, screening, grinding, washing the resulting sand and gravel. In the absence of natural sand areas, often using artificial aggregate pouring concrete. Artificial aggregate production process are: wool mining, processing coarse aggregate, fine aggregate processing, screening, after washing reserves and transportation. Advantages of artificial aggregate are: ① wool stope nearest arrangements, reduce storage, loading and transport links, saving investment; ② to adjust production mix than the aggregate of all levels make full use of wool, save mining cost; ③ artificial aggregate particle size distribution is good, save cement, fresh surface roughness to increase bond strength, good mechanical properties. The disadvantage is the need to increase drilling blasting, crushing, sieving, washing, sand and other processes, the process is cumbersome, install more equipment and a greater direct costs of the system. Wool sand by crushing, screening, grinding, wa
阅读全文

Raymond Mill grinding system new advantages

Raymond Mill is a kind of grinding equipment that we commonly use in industrial ultrafine mill . It is suitable for limestone, calcite, marble, talc, gypsum, barite, fluorite, zeolite, manganese ore, ilmenite, phosphorus Minerals, bentonite, starch, kaolin and other stones with a hardness of less than Mohs 7 are ground and used in a wide range of applications, all of which are inextricably linked to its new grinding system. So what technology is applied to the grinding system used by Raymond Mill? 1. The new technology adopts a new vertical roll device. The grinding roller and the grinding ring are always in balance during the grinding process to form a uniform line contact grinding zone. The height of the grinding roller and grinding ring is increased from the original 160 mm to 200 mm, which increases the grinding contact area to a greater extent. 2. The classifier adopts a forced turbine classifier to extend the granularity of the finished product from the original 80-325 mesh range
阅读全文

New sand maker consolidates infrastructure construction

Since the 18th National Party Congress, our country has been inclined tocontinue to invest heavily in infrastructure to promote economicbooming, which will further expand the market demand for vsi sand making machine and gravelaggregate. In the face of the huge gravel aggregate demand, it isnecessary for gravel equipment R D manufacturer to activelyprepare for high-tech sand making machine to help the rapid development of economy. Sand making equipment is the key to the production of high-quality sandand gravel aggregate, the quality of sand and gravel aggregates directlyaffects the quality of infrastructure works. For a long time, theoverall technical level of sand making is low; facing increasinglystringent technical and quality requirements in the market, China sandmaking machine manufactures require to take active innovation, furtherincrease R D investment on technological application to meet thehigh standards and high demand of the market. Hongxing machine deeply understands
阅读全文