How to deal with accidents in the production of sand making machine

How to deal with the accident situation of the sand making machine production? The office of the Shanghai SBM Heavy Industry Sand Making Machine has summed up the problems arising from the production of the sand making machine in the past year. Today, how to deal with the unexpected situation: 1. Installation position of the sand making machine: cavity The pressure and flow inside the body can improve the production efficiency, but in the case of the two premise, the sand making machine parts should be installed in place as much as possible. For example, the height of the grinding roller and the grinding ring should be kept horizontal, and the eccentric rubber sleeve can be used to adjust the level; the blade between the blade and the grinding roller should maintain a gap of about 10 cm and maintain an angle of 23 degrees with the grinding bottom. 2. Evenly feeding: the speed of feeding will often enter a misunderstanding. The larger the quantity, the better, the output will increase. This is not the case. If the amount is too large, it will cause poor mechanical operation. As the saying goes, even sand is made. sand making machine; therefore, the feeding should follow the principle of uniform feeding, not too large or too small. 3. The influence of the humidity of the material: Most of the mills on the market are dry and brittle, and the materials with low water content have good milling effect, high speed and high efficiency; on the contrary, they are sticky and soft, sticky and hard, including The material with large amount of water is easy to stick to the blade of the blade, resulting in poor mechanical operation and low production efficiency. 4. Lower pressure valve: can only be pressed down, never lift up, otherwise it will cause the mill to leak, it takes about five minutes, the pressure inside the cavity is enough, can continue to discharge. In the actual operation process, if the accident situation is often encountered, resulting in the equipment can not be produced normally, it is because of lack of experience, not good at summing up in the usual work. I hope that everyone can do a good job of the above four points in the future production, pay attention to the details, and ensure the smooth progress of production. As long as we do this, we can quickly increase the productivity of our equipment.

评论

发表评论

此博客中的热门博文

Artificial aggregate production process and advantages and disadvantages

Wool sand making machine by crushing, screening, grinding, washing the resulting sand and gravel. In the absence of natural sand areas, often using artificial aggregate pouring concrete. Artificial aggregate production process are: wool mining, processing coarse aggregate, fine aggregate processing, screening, after washing reserves and transportation. Advantages of artificial aggregate are: ① wool stope nearest arrangements, reduce storage, loading and transport links, saving investment; ② to adjust production mix than the aggregate of all levels make full use of wool, save mining cost; ③ artificial aggregate particle size distribution is good, save cement, fresh surface roughness to increase bond strength, good mechanical properties. The disadvantage is the need to increase drilling blasting, crushing, sieving, washing, sand and other processes, the process is cumbersome, install more equipment and a greater direct costs of the system. Wool sand by crushing, screening, grinding, wa
阅读全文

Raymond Mill grinding system new advantages

Raymond Mill is a kind of grinding equipment that we commonly use in industrial ultrafine mill . It is suitable for limestone, calcite, marble, talc, gypsum, barite, fluorite, zeolite, manganese ore, ilmenite, phosphorus Minerals, bentonite, starch, kaolin and other stones with a hardness of less than Mohs 7 are ground and used in a wide range of applications, all of which are inextricably linked to its new grinding system. So what technology is applied to the grinding system used by Raymond Mill? 1. The new technology adopts a new vertical roll device. The grinding roller and the grinding ring are always in balance during the grinding process to form a uniform line contact grinding zone. The height of the grinding roller and grinding ring is increased from the original 160 mm to 200 mm, which increases the grinding contact area to a greater extent. 2. The classifier adopts a forced turbine classifier to extend the granularity of the finished product from the original 80-325 mesh range
阅读全文

New sand maker consolidates infrastructure construction

Since the 18th National Party Congress, our country has been inclined tocontinue to invest heavily in infrastructure to promote economicbooming, which will further expand the market demand for vsi sand making machine and gravelaggregate. In the face of the huge gravel aggregate demand, it isnecessary for gravel equipment R D manufacturer to activelyprepare for high-tech sand making machine to help the rapid development of economy. Sand making equipment is the key to the production of high-quality sandand gravel aggregate, the quality of sand and gravel aggregates directlyaffects the quality of infrastructure works. For a long time, theoverall technical level of sand making is low; facing increasinglystringent technical and quality requirements in the market, China sandmaking machine manufactures require to take active innovation, furtherincrease R D investment on technological application to meet thehigh standards and high demand of the market. Hongxing machine deeply understands
阅读全文