Quarry stone crushing equipment commonly used jaw crusher for daily use strategy

Infrastructure development cannot leave the concrete, cement and sand and gravel aggregate is made, and the material from stone crushing equipment of high quality, highly effective, commonly used in a Quarry Crusher, jaw crusher with the highest value, is to provide high quality for the urban construction of choice for application of broken equipment, for hard or hard material of broken, it can deal with, it has simple structure, convenient repair and maintenance of properties is the main factor to win the market. How to eliminate these so-called & other; Question & throughout; , small make up for this sums up the following & other; Question & throughout; : 1, work clang, lining board jitter. This phenomenon is due to the crushing cavity side plate and more loose tooth plate (,), tighten the screw loose or rupture caused by, should tighten or replace in a timely manner. 2, after knee fracture frequently. After bracket in addition to the transmission power is depend on the strength of the shortage of the insurance. In addition to the central bracket intensity is low, its strength is not enough to overcome damage due to normal crushing force produced by crushing ore, may be too tightly on the lever spring, coupled with crushing force at work overload and fracture, can adjust appropriately loose spring. 3, crusher run idle, lower metal sound. The possible causes of has the following three aspects: (1) broken mobile jaw and fixed jaw teeth board sound, is caused by row ore mouth is too small. Plate (2) the thrust bearing or gasket in adjusting device in the crash, general is due to the pull rod buffer spring elastic disappear or damaged, or rotational spring pressure is not tight. (3) it is also possible that bracket bearing slider wear serious or relaxation, the bracket head wear. 4, flywheel swing dramatically, eccentric shaft rotation is slow. The fault system as part of the pulley and the flywheel key loose or damaged, can''t synchronous wheel and axle. 5, broken product granularity coarsens, this is the result of severe wear of broken plate bottom. Tooth plate should be up and down a transfer or replace a new lining board, adjust the row ore mouth to reach the requirements of the size. 6, the flywheel Quarry Crusher does not work. Reason is due to the damage of tie rod spring and pull rod, tie rod nut tripping bracket from bearing slider pull, can also be bracket broke off, and should be replaced to install.

评论

发表评论

此博客中的热门博文

Artificial aggregate production process and advantages and disadvantages

Wool sand making machine by crushing, screening, grinding, washing the resulting sand and gravel. In the absence of natural sand areas, often using artificial aggregate pouring concrete. Artificial aggregate production process are: wool mining, processing coarse aggregate, fine aggregate processing, screening, after washing reserves and transportation. Advantages of artificial aggregate are: ① wool stope nearest arrangements, reduce storage, loading and transport links, saving investment; ② to adjust production mix than the aggregate of all levels make full use of wool, save mining cost; ③ artificial aggregate particle size distribution is good, save cement, fresh surface roughness to increase bond strength, good mechanical properties. The disadvantage is the need to increase drilling blasting, crushing, sieving, washing, sand and other processes, the process is cumbersome, install more equipment and a greater direct costs of the system. Wool sand by crushing, screening, grinding, wa
阅读全文

Raymond Mill grinding system new advantages

Raymond Mill is a kind of grinding equipment that we commonly use in industrial ultrafine mill . It is suitable for limestone, calcite, marble, talc, gypsum, barite, fluorite, zeolite, manganese ore, ilmenite, phosphorus Minerals, bentonite, starch, kaolin and other stones with a hardness of less than Mohs 7 are ground and used in a wide range of applications, all of which are inextricably linked to its new grinding system. So what technology is applied to the grinding system used by Raymond Mill? 1. The new technology adopts a new vertical roll device. The grinding roller and the grinding ring are always in balance during the grinding process to form a uniform line contact grinding zone. The height of the grinding roller and grinding ring is increased from the original 160 mm to 200 mm, which increases the grinding contact area to a greater extent. 2. The classifier adopts a forced turbine classifier to extend the granularity of the finished product from the original 80-325 mesh range
阅读全文

New sand maker consolidates infrastructure construction

Since the 18th National Party Congress, our country has been inclined tocontinue to invest heavily in infrastructure to promote economicbooming, which will further expand the market demand for vsi sand making machine and gravelaggregate. In the face of the huge gravel aggregate demand, it isnecessary for gravel equipment R D manufacturer to activelyprepare for high-tech sand making machine to help the rapid development of economy. Sand making equipment is the key to the production of high-quality sandand gravel aggregate, the quality of sand and gravel aggregates directlyaffects the quality of infrastructure works. For a long time, theoverall technical level of sand making is low; facing increasinglystringent technical and quality requirements in the market, China sandmaking machine manufactures require to take active innovation, furtherincrease R D investment on technological application to meet thehigh standards and high demand of the market. Hongxing machine deeply understands
阅读全文