轩轩阁

The crusher looks like a simple mechanical device, and it will encounter many problems in production. No matter the size or the problem, it is normal for the mechanical equipment. After all, the unfinished mechanical equipment is also produced by human beings. Simple, about the base break of Crusher Plant , I think this is a big problem, customers should not underestimate all the problems that occur on the mechanical equipment. The following small series introduces the treatment method of the broken base of the crusher, and hope that the majority of customers pay attention to this problem. The vibration energy generated by the normal operation of the crusher is insufficient to cause the substrate to break. Mostly due to the unstable factors in the operation of the crusher: if the crushing chamber of the crusher is seriously blocked, the mechanical vibration will be generated, which will have a great influence on the substrate. After many similar vibrations, it is likely to A base fra

Tri-ring grinding is a processing equipment for fine powder and ultra-fine powder. The Trapezium mill is mainly suitable for processing non-flammable and explosive brittle materials with Mohs hardness <6 grade. China as a developing country, three-ring grinding There are many applications, and China's mineral resources and types are also relatively complete, and the degree of mineral self-sufficiency is also one of the countries with higher levels of self-sufficiency. As a non-renewable resource, mineral resources are also very limited. How to fully utilize and develop mineral resources is the future development direction. Sanhuan can improve the comprehensive utilization efficiency of mineral resources and thus the effect of limited resources. . While processing the minerals, the tricyclic grinding has a direct relationship between the utilization of resources and the fineness of the materials. Taking coal as an example, the finer the fineness of processing, the larger the co

For the energy-saving problem of milling equipment, users and manufacturers are very concerned. Among them, manufacturers are mainly concerned with how to reduce the energy consumption under certain production effects, while users care about how to improve grinding under certain energy consumption. Powder production efficiency and production quality issues. The two are mutually influential. Therefore, we should pay attention to how to reduce the energy consumption of the cement vertical roller mill, and then further improve the machine performance, so that the user's production is protected. Among them, the ventilation of the cement vertical roller mill can discharge the steam and fine powder in the mill, and can also reduce the phenomenon of grinding in the mill. At the same time, it can also prevent the ball and blockage, reduce the temperature inside the mill, improve the grinding condition and improve the production. effectiveness. Therefore, it can be seen that in production

Shanghai SBM specializes in the manufacture of grinding machines. Among them, ultra-fine grinding machines, Vertical Roller Mill , Raymond mills and other equipment have been loved by customers. Today, we mainly share 800-mesh calcium carbonate vertical. The production line configuration scheme of the mill. Next, let's talk about it with Xiaobian. If you want to grind calcium carbonate, Xiaobian thinks that it is very important to choose the grinding machine. The vertical mill is the mainstream production equipment in the milling industry. It can be equipped with fine powder 325-3000 mesh and calcium carbonate vertical milling. The machine is also an energy-saving and environment-friendly milling equipment, and is the preferred pulverizer for customers. Calcium carbonate is an inorganic compound commonly known as: limestone, limestone, stone powder, marble. When it comes to calcium carbonate powder, its use is still quite extensive and can be used in food, construction, paper, pai

High-pressure mill plays an important role in ore mining and processing. In the grinding production process, there are many factors affecting the output of high-pressure mill. We need to understand it to better ensure the production of Trapezium Mill . ability. 1. The hardness of the material. Regardless of the powder processing equipment, the harder the material is, the more difficult it is to grind, and the more severe the wear on the equipment components. In this case, it will inevitably affect the production capacity of the high-pressure mill, resulting in a decrease in production. 2. The granularity of the material. Under the same milling conditions, the longer the larger material is ground, the lower the efficiency of the equipment. In view of this situation, we want to improve the output of the high-pressure mill, it is best to properly control the particle size of the material, not only to ensure that the particle size of the material is within the appropriate size range, but

The rod mill has the same structure as the ball mill. The difference lies in the shape of the grinding medium: one is a steel rod and the other is a steel ball. The stick mill has simple orange, easy operation and reliable operation. It is suitable for rock with various hardnesses. Sand, the product particle size distribution is excellent, as long as the sand selected to the desired fineness modulus is controlled, the sand composition is generally consistent. Generally speaking, the rod grinding mechanism sand has no super-diameter particles and the grain shape is also good. As long as the parameters of the operation are determined to be constant, the fineness modulus of the sand can be stably controlled within ±0.20, and it is possible to reach within ±010. The operating parameters of the sand making equipment depend on the following factors, the physical properties of the rock, the grain size of the rock mass, the grinding ratio, the amount of the rod, the ratio of the rod diameter,

The stone crusher cylinder has a conical shape and is mainly made of steel material welded and cast. The role of the cylinder in the equipment is to improve the production environment for the material and reduce the wear of the parts. At the same time, the service life of the Stone Crusher cylinder can be improved, and reasonable maintenance is required. Then, let's introduce the maintenance work of the stone crusher cylinder. 1. The inspection of the stone crusher cylinder is the primary task. Regular inspection of the equipment cylinder can avoid the occurrence of safety hazards. The inspection items include the wear of the inner wall of the cylinder, the tightness of the fastener of the cylinder, and the corrosion of the surface of the cylinder. If these phenomena are found, they should be treated in time to avoid malfunction. 2. Since the stone crusher often performs fine crushing or superfine crushing operations, it is inevitable that a large amount of dust will be generate

The bearing is the core part of the cobblestone sand making machine , and it is also a part that is easy to wear. If the bearing is not repaired after the damage, the bearing wear will cause the bearing clearance to be too large, and the bearing clearance will become larger, which will affect the production efficiency. . The bearing of the cobblestone sand making machine is a spherical roller bearing with an adapter sleeve. The fixing is tightened by the fastening sleeve. When the locking is required, the nut needs to be squeezed in the bearing to promote the bearing and the tightness. Mutual movement between the sleeves makes the bearing and the adapter sleeve outer ring tightly fit. If the bearing and the adapter sleeve are not installed during installation, it is prone to heat and enthalpy when the test machine is tested. Axis phenomenon, long-term operation is likely to cause excessive bearing clearance. When the load is applied, if the clearance is too large, the radial and axia

SBM Raymond Machine Factory has focused on Raymond Mill for more than 20 years and summed up a series of experiences. After Raymond Mill has been operated and adjusted, the work efficiency has increased dramatically. Below we will share the method with SBM: Raymond mills generally do not adjust during normal work. Raymond mills that have just started work, or Raymond mills that have just been repaired need to be adjusted. When adjusting the Raymond mill, find out the control details of the wind main delivery system. The work should adjust the rotation speed of the rotary vane analyzer according to the requirements of the powder. In order to ensure the stability of the particle size of the Raymond mill and ensure the work efficiency of the Raymond mill, it should always keep enough raw materials in the mainframe. The feeder feeds evenly. When the Raymond mill needs to stop, first stop the work of the feeder and close the rack insert. After the raw materials left by the main machine ar

The overpressure type mill is a kind of trapezium mill . Firstly, the stone material is mixed by the screw equipment in the equipment, and then the soil in the stone guess is mixed with water and discharged from the flow port on the equipment. The stone material is gradually selected by the action of the screw device, and is discharged from the discharge port at the top, and then the cleaning and picking action of the sand stone material is realized. If you want to purchase a more excellent over-pressure trapezium mill equipment, then you have to carefully purchase, but because we are not very familiar with these equipment, so introduce some about the purchase of overpressure ladder type A small method of grinding machine, under the premise of ensuring quality and output value, select equipment with lower cost. First, when purchasing the overpressure trapezium mill, it is more common to question the customers from the aspects of the multi-step trapezium mill. For example, the functio

The slagging function of Raymond Mill means that Raymond Mill can discharge harder slag out of the grinding chamber, which can improve the quality of the powder or extract the finished product. Raymond Mill's slagging function is mainly used in the following industries: First, the separation of hard impurities, at this time the dregs are waste products, if ground into the powder, it will increase the impurities of the powder, reducing the purity and quality of the powder. For example, in the charcoal industry, in the process of anaerobic firing, charcoal will use different wood materials, which will be doped with impurities such as earth, quartz, pebbles and so on. Charcoal or hemp charcoal is mainly used for mosquito coils or gunpowder, fireworks, etc., burning is their ultimate value, but if there are impurities, especially fireworks or wires, it will greatly reduce its burning performance. This is the function of slagging. Raymond mill's slagging can remove limited stones

When the mobile crushing station is used, the role of the lubricating oil is mainly to reduce the wear, but its effect is not only the case. When the lubricating oil is missing, it will have a great impact on the equipment, mainly in four aspects: Temperature, speed, load and impact load changes, here is a detailed introduction to these four aspects. First, temperature changes One of the functions of lubricating oil for moving crushing stations is to control the temperature and prevent the high temperature deformation of its parts. Therefore, the lack of lubricating oil will cause changes in its temperature, and the characteristics of lubricating oil itself will change with temperature. It will change. Generally speaking, if the temperature is too low, it will become thicker. If the temperature is too high, it will become thinner. In this case, when the lubricant is used, it should be selected according to different temperatures. To choose a lubricant with a high consistency, if the we

Vertical mill grinding machine is widely used in the production of non-metallic minerals, and is also a common processing clay equipment. Customers who grind 200 mesh clay powder can recommend the processing clay equipment produced by the manufacturer. SBM heavy machine has rich experience in the clay field, providing clay customers with more professional clay powder grinding machine to meet customers. The production demand of 200 mesh clay powder, and the price of SBM heavy machine clay Vertical Roller Mill is reasonable, the working principle is more scientific, and the customer's support is obtained. As a professional manufacturer of processing clay equipment, SBM Heavy Machine has always created benefits for each powder project with excellent quality and perfect after-sales service. SBM heavy machine team has rich experience in machining and manufacturing, and also has more perfect after-sales service. The system has established offices and service centers in many regions to

The cone crusher is a crushing device commonly used in production. Spindle breaks are a common type of failure during production runs. Frequent breaks in the spindle not only affect normal production, but also aggravate routine maintenance and overhaul work. For this fault, this paper analyzes the cause of the fault and finds a solution. A detailed analysis of the causes of the main shaft fracture and the solutions are as follows. First, the reason for the broken shaft (1) The strength of the main shaft is weak: the static fit between the main shaft and the broken vertebral body causes stress concentration on the main shaft section, which significantly reduces the fatigue strength of the main shaft material. The main shaft gradually cracks during the crushing process of the crusher. The bending stress at the stress concentration of the spindle is broken beyond the strength of the material. (2) Overload operation: Due to insufficient spring pressure, the upper support sleeve of the cr

Raymond mill is a kind of milling machine imported from abroad. After the raw material of the ore is simply broken and crushed by the jaw crusher, it is transported to the storage bin by the bucket elevator, and then the material is transferred to the main grinding chamber of the Raymond mill through the electromagnetic vibration motor of the discharge port of the silo. The semi-finished fine powder is ground between the grinding roller and the grinding ring, and the fine powder is brought to the analysis machine by the fan airflow, and analyzed and screened by the analysis machine to meet the process requirements, and the air is brought to the large cyclone collector by the airflow. Auxiliary equipment for Raymond mill equipment. Here are a few common faults. The parts are loose, and the parts that are newly processed and assembled have geometrical deviations. Because of the alternating load such as impact and vibration, as well as the influence of heat and deformation, and the wea

When it comes to the users of the river pebble sand making machine , it is a strange problem to replace the wearing parts. It is very troublesome to replace the parts when replacing the parts. Many manufacturers come to see the equipment production efficiency. Very satisfied is not satisfied with this replacement parts, and later through the communication with the customer can not design a more convenient replacement parts of the machine. After a thorough investigation and experiment, we have developed a one-button hydraulic unpacking river pebble sand making machine. This machine not only replaces the accessories, but also is more suitable for preventing material blockage. So simple to say about the superior aspects of the open-box river pebble sand making machine, our users are a constant source of inquiries, how is our river pebble sand making machine out of the box, open box type river pebble sand making machine is convenient Where is the new type of river pebble sand making machi

Limestone mill is a very wide range of materials used in various industries. The application of industrial development in different industries in China has a corresponding range. Each ore material can be processed very well after processing. However, if limestone is to be applied to various industries, it needs to be processed by ore processing equipment. We have corresponding analysis for the processing application of limestone mill because its application fields are relatively fine. Such as building materials, paints, etc., these are places where limestone can be applied. After the analysis of the application requirements of the limestone mill and the corresponding manufacture of the equipment, the grinding equipment of various capacities is used to pave the way for the production of limestone, because not every industry has the same application for limestone, so its processing The equipment is also different, the limestone mill is used by more and more industry manufacturers in th

Vertical mill grinding machine is widely used in the production of non-metallic minerals, and is also a common processing clay equipment. Customers who grind 200 mesh clay powder can recommend the processing clay equipment produced by any manufacturer. SBM has rich experience in the production of clay, and provides clay customers with more professional clay powder grinding machine to meet customers' 200 mesh. The production demand of clay powder, and the price of SBM clay vertical roller mill is reasonable, the working principle is more scientific, and it is supported by customers. As a professional manufacturer of processing clay equipment, SBM has always created benefits for each powder project with excellent quality and perfect after-sales service. SBM team has rich experience in machining and manufacturing, and also has a more perfect after-sales service system. The region has established offices and service centers to create significant market benefits for each customer in a

What are the reasons that affect the failure of Raymond mill gears? First, the special working environment of Raymond mill , in the production process, the gear transmission environment is relatively harsh, after being affected by dust particles, it is easy to cause serious gear pollution. And if the lubricating oil in the gear transmission part is not added in time, it is easy to cause the gear transmission of the equipment to fail. Second, after the gear transmission is operated for a period of time, the axes of the pinion and the classifying drum are not parallel, resulting in local engagement of the gears. Moreover, the gear is unevenly stressed during the whole production process, which easily causes the gear shaft to bend. In addition, the gear transmission material is not uniform, and particles, entrainments, and the like are apt to exist, and the surface stress is excessively large, causing a broken tooth. Third, there is stress on the Raymond mill gear. When the gear enters

Most of the users of open pit mines are power plants, and the coal supply requirements for power plants are less than 200 mm. Most small and medium-sized open-pit coal mines do not have Portable Crusher Plant . The particle size of coal does not meet the requirements, which directly affects the economic benefits of coal mines. The establishment of a fixed crushing station not only has a one-time investment, but also increases the secondary reversal link, which increases production costs. It also affects the economic benefits of coal mines. Open-pit coal mines have top-down rock layers, including cemented gravel layers and Jurassic strata, medium sand holes and fine sandstones. The rock mass is dense, hard, and uniform in structure. Moreover, under the condition of crushing, different types of rock and soil have different vibration responses to the fracture. Since the coal-bearing stratum is a homogeneous rock mass, the ability to accept the propagation of detonation waves is related t

The main component of limestone is calcium carbonate, which is an important raw material in industrial production. It is ground into powders of different fineness such as soda powder, double fly powder, three fly powder and four fly powder. It can be used to make glass and plastic. Putty powder, paint, plywood, paint, rubber, ink and other materials are widely used in chemical, building materials, construction, metallurgy, light industry and other fields. There is user consultation: What are the complete sets of equipment for the grinding of limestone? What is the investment cost? This article provides a detailed answer. What are the complete sets of limestone milling equipment? China's limestone resources are abundant and distributed throughout the country. Therefore, limestone mill is relatively common, and the treatment process is relatively simple. The general processing flow is crushing, sieving, milling, etc. The equipment used has a jaw crusher. Counter-crusher, Raymond m

The feeding control of Upgraded version of Raymond Mill is very important, which is related to the grinding efficiency and particle size of the mill. The following to introduce the feeding machine control and automatic feeding method of setting. Ramond mill feeding machine adopts electromagnetic vibration feeding mode. The point vibration machine is a double particle directional forced vibration system. The armature is composed of a tank, an armature and a vibrating fork. The whole electric vibration feeder should be suspended in a free state, there should be a certain clearance around, there should be no collision between the material and the feeder, so as to avoid noise during work. After the installation, loosen the screws used for locating and connecting the fork check (three on the top and one on the bottom of the vibrator), and tighten the lock nut after loosening. Open the vibrator back cover, check with armature iron core air gap within the scope of 1.8-2.1 ㎜, whether parall

Vertical mills cause some common problems due to long-term continuous work. These common problems are relatively common. Users can repair them themselves or have them be repaired by the maintenance personnel of the machine. However, users need to have a simple understanding of these common problems. The specific contents are as follows. It is extremely easy to consume wear parts in the vertical grinding work, and these wear parts include grinding rolls and grinding discs. The grinding roller and the grinding disc are installed according to the specific design principle. The Vertical Roller Mill produced by the company can be idling for a period of time, which means that the grinding roller and the grinding disc are not in contact. When there is a problem with the installation between the two, the wear between the two will be intensified, and the wear of the components will create a groove under the continuous scouring between the hot air and the material, so that the collision betwee

The VSI series of new sand making machine is a new generation of sand making machines with a level. Years of technical accumulation, modern processing equipment and precision production ensure the status of the VSI series of new sand making machines. Excellent cost performance and reliability in similar products. The VSI series high-efficiency vertical shaft impact crusher is a new generation of new sand making equipment that has been specially designed and developed, and has been designed and manufactured. It is also a horizontal high-performance sand making equipment. This machine is specially designed for highways, high-speed railways, high-rise buildings, municipal, hydropower dam construction, concrete mixing stations, and is the preferred equipment for artificial sand and stone shaping. Product Features: 1. Large processing capacity and high output – compared with traditional equipment under the same power, the output is increased by 30%, and the operation is stable; 2, low con

The VSI series of new sand making machine is a new generation of sand making machines with a level. Years of technical accumulation, modern processing equipment and precision production ensure the status of the VSI series of new sand making machines. Excellent cost performance and reliability in similar products. The VSI series high-efficiency vertical shaft impact crusher is a new generation of new sand making equipment that has been specially designed and developed, and has been designed and manufactured. It is also a horizontal high-performance sand making equipment. This machine is specially designed for highways, high-speed railways, high-rise buildings, municipal, hydropower dam construction, concrete mixing stations, and is the preferred equipment for artificial sand and stone shaping. Product Features: 1. Large processing capacity and high output – compared with traditional equipment under the same power, the output is increased by 30%, and the operation is stable; 2, low con

For the sand machine workflow, many customers think that as long as the production line, the rest is fine. This idea is incorrect and unscientific. In order to enable customers to have a correct understanding of the working process of the sand making machine , Shanghai SBM mechanical professional and technical personnel summarized the problems needing attention in equipment installation as follows: During the installation of sand making production line equipment, if the equipment is not properly installed, the whole production line will not be able to work normally, which will also bring harm to the machine itself, as well as personal threats to sand making operators. Sand making machine is mainly composed of hopper, distributor, vortex crushing chamber, impeller, spindle, base, transmission device, bracket and other components of a sand making equipment. Methods to improve the efficiency of the sand making machine: the sand making machine should be lubricated regularly. The lubricat